For engraving | |||
Material | Speed (mm/min) | Power (%) | Times |
Plywood | 6000 | 50 | 1 |
Acrylic | 6000 | 20 | 1 |
Leather | 6000 | 20 | 1 |
Electroplated | 1000 | 100 | 1 |
Powder coating | 6000 | 50 | 1 |
Anodic alumina | 6000 | 20 | 1 |
Stainless steel | 6000 | 100 | 1 |
Density board | 6000 | 60 | 1 |
Peddle | 6000 | 100 | 1 |
Plastic board | 6000 | 40 | 1 |
Cardboard | 6000 | 50 | 1 |
For Cutting | |||
Material | Speed (mm/min) | Power (%) | Times |
Plywood 1mm | 600 | 100 | 1 |
Plywood 2mm | 450 | 100 | 1 |
Plywood 3mm | 280 | 100 | 1 |
Plywood 4mm | 200 | 100 | 1 |
Plywood 5mm | 150 | 100 | 1 |
Plywood 6mm | 100 | 100 | 1 |
Plywood 7-8mm | 100 | 100 | 1—2 |
Acrylic 1mm | 500 | 100 | 1 |
Acrylic 3mm | 200 | 100 | 1 |
Acrylic 6mm | 100 | 100 | 1—2 |
Model No. | TS3 |
---|---|
Laser power | 10W Compressed spot laser |
Laser wave length | 445±5nm |
Output power | 35W-40W |
Material | Aluminum profile + metal |
XY Axis Positioning Accuracy | 0.1mm |
Engraving Size | 14.2" (300*200mm) |
Engraving accuracy | 0.08mm |
Engraving speed | 10000mm / min |
Engraving method | USB / APP / Online / Screen Operation |
Engraving materials | Stainless steel |
Document format | NC、DXF、BMP、JPG、PNG、GCODE |
Engraving mode | Image carving、Test carving、Scanning carving、Contour carving、Pixel carving |
Support system | Windows |
Support Software | LaserGRBL / Lightburn |
Machine Size | 570*430*270mm |
Package Size | 630*500*330mm |
Machine Weight | 14.4kg |
Package Weight | 16kg |
User Manual | English Manual |
Firmware | Please confirm the current vision of your device before downloading and upgrading your firmware to avoid causing problems. It's recommended to contact our technical support first before upgrading. |
Drive | CH340SER |
Software | LASERGRBL | LIGHTBURN |
TF Card Files | Download |
Testing Files | Download |
5. Click the move button to see if the machine moves properly.
2.1 Screen interface introduction;
2.1.1. Laser out of the light of the interface (manual control of the laser on).
2.1.2. Control interface (move, set home, return home, unlock, return to zero, etc.);
2.1.3. Engraving page (read TF card file).;
2.1.4. Setup page (firmware version information, switching Y-axis and rotary table, WiFi information).
2.2 Execute the engraving process using the screen;
2.2.1 Computer editing file (.nc or .Gcode file) needs to be saved to the TF card first;
2.2.2 Inserting the TF card into the machine;
2.2.3 Select the file to be engraved and enter the engraving setting interface;
2.2.4 Move to the desired location and click on Set Origin;
2.2.5 Click on the edge patrol, if the position is not suitable, repeat the previous operation;
2.2.6 If the position is correct, click “√” in the pop-up window to start engraving.1.Open the software and connect the machine.
5. Start engraving.
Gcode files can be generated by lightburn or GRBL software on your computer by:
1 Open the software and drag in the files to be engraved;
2 Set the appropriate parameters;
3. Save the file as a Gcode file.
14.1. Preparation for APP use;
1. Install the app on your phone (download it from the application mall or open the TF card to find the installation package for installation);
2. Open the machine settings page;
3. Use your phone to connect to the machine WiFi;
4. Open the APP enter the IP address on the machine screen and click connect;
5. Enter the operation interface and start using APP;
6. Insert the TF card to use as storage data.
14.2. Use the APP to execute the engraving process ;
14.2.1 Select the pattern you want to engrave in the creation module or in the file list (you can upload album pictures) ;
14.2.2 Click next for pattern setting ;
14.2.3 Click next for parameter setting (size, power, speed) ;
14.2.4 Click Move for position selection.;
14.2.5 check whether the position is correct by the edge patrol function (repeat the previous step if it is not correct);
14.2.6 Click Engrave to upload the file to start engraving..
15.1. Preparation for Web use;
15.1. Use the APP to execute the carving process;
15.1.1 Enter $H in the input box of the control interface to make the machine return to zero; 15.1.2 Select a file or upload a local file in the “SD File” interface;
15.1.3 Enter the control interface to set parameters (power, speed);
15.1.4 Move the position and determine the home position;
15.1.5 Check if the position is correct by using the (if not, repeat the previous step);
15.1.6 Click the engraving button to start engraving.
1. Check whether the belt of each axis has tension, and re-adjust the tension of the timing belt;
2. Whether the machine hardware (screws, etc.) is tightened;
3. Check the condition of the machine transmission parts have no jamming or loose collapse shaking;
4. Adjust the eccentric nut around the transmission position;
5. Fxed laser parts screws are not locked, not locked will lead to shaking (laser head focus knob loose lead to focus change).
1. Adjust the eccentric nut;
2.Adjust the belt tightness;
3. Check the fastener screws for looseness and Re-tighten.
Note: When this function needs to be turned off, it can be adjusted to the lowest.
Note: the parameters are for reference only, there will be deviations due to the material.
Note: the parameters are for reference only, there will be deviations due to the material.
Note: the parameters are for reference only, there will be deviations due to the material.
Note: the parameters are for reference only, there will be deviations due to the material.
1.remove the honeycomb board ;
2. Put the item on the next layer before carving.
If the problem is not solved: please try to replace the other engraving files to test (through the engraving software to reset the size of the engraving pattern, and the output of a new engraving file).
GRBL software:
Lightburn software: